Jun-2024 Pass Your NACE-CIP2-001 Exam at the First Try with 100% Real Exam
Get Real Exam Questions for NACE-CIP2-001 with New Questions
NACE-CIP2-001 (Coating Inspector Level 2) Certification Exam is designed to test the knowledge and skills of individuals who are involved in the inspection and quality control of protective coatings. Coating Inspector Level 2 certification is offered by the National Association of Corrosion Engineers (NACE), which is a globally recognized organization that provides training and certification programs in the field of corrosion prevention.
NACE-CIP2-001 certification is highly valued by employers in industries such as oil and gas, marine, aerospace, construction, and transportation. It is also recognized by regulatory bodies and government agencies as a standard for quality control and assurance in coating inspection and evaluation. With this certification, professionals can enhance their credibility and demonstrate their commitment to excellence in the field of corrosion control and protective coatings.
Obtaining the NACE-CIP2-001 certification is a significant achievement for professionals in the field of coating inspection. Coating Inspector Level 2 certification demonstrates that the individual has a strong understanding of coating inspection principles and is able to apply this knowledge in practical situations. Coating Inspector Level 2 certification is recognized by many industries, including oil and gas, marine, and construction. It also provides opportunities for advancement in the field of coating inspection, including higher-level certifications and leadership positions.
NEW QUESTION # 34
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. Cold flow or creep
- B. No difference from any other coating
- C. A very high reading
- D. A very low reading
Answer: A
NEW QUESTION # 35
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Concrete
- C. Heat-shrink sleeves
- D. Liquid epoxies
Answer: D
NEW QUESTION # 36
When observing design defects the NACE Inspector should:
- A. Document the defect and the potential problems that could result
- B. Ignore the defect as the inspector can't change the design
- C. Request that the item be rebuilt with a better design for coating
- D. Stop the job immediately
Answer: A
NEW QUESTION # 37
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Correct the errors yourself and suggest the Level 1 inspector be replaced
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
Answer: D
NEW QUESTION # 38
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Appearance
- C. Safety
- D. Iron content
Answer: D
NEW QUESTION # 39
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. have a cross-linked polyethylene backing and a heat-activated adhesive.
- C. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- D. is typically green or led and looks like "painted" finish.
Answer: C
NEW QUESTION # 40
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION # 41
Individuals conducting Coating Surveys should:
- A. Always be NACE Level 3 Certified Inspectors
- B. Always be experienced Specification Writers
- C. Always be trained and experienced Coating Industry
- D. Always be NACE or SSPC Protective coating Specialists
Answer: C
NEW QUESTION # 42
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Acid etching
- B. Sacking
- C. High-pressure water washing
- D. Stoning
Answer: B
NEW QUESTION # 43
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Air changes
- B. a), b), and c)
- C. Lighting
- D. Structural integrity
Answer: B
NEW QUESTION # 44
Corrosion is the reverse process of
- A. steel manufacturing.
- B. galvanic deterioration.
- C. hot dipping.
- D. flaking.
Answer: A
NEW QUESTION # 45
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Mainline coating
- D. Areas exposed to Ultra Violet light
Answer: B
NEW QUESTION # 46
Ideally, documentation requirements should be defined:
- A. In the specification
- B. By the contractor
- C. At the pre-job conference
- D. By the inspector
Answer: A
NEW QUESTION # 47
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Magnetic Gauge
- C. Ultra Sonic DFT Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION # 48
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- B. Determine the Dry Film Thickness of the coating prior to use
- C. Ensure the glue on the dolly is properly applied prior to use
- D. Consult SSPC Guide 1 prior to use
Answer: B
NEW QUESTION # 49
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Flow stage
- B. Gel stage
- C. Cure stage
- D. Wetting stage
Answer: A
NEW QUESTION # 50
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Comparable to air blast cleaning
- B. Different than air blast cleaning
- C. Slightly different to air blast cleaning
- D. The same as air blast cleaning
Answer: D
NEW QUESTION # 51
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 50 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 double rubs with a saturated cloth.
- D. 25 single rubs with a saturated cloth.
Answer: A
NEW QUESTION # 52
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. coatings are expected to degrade over time.
- C. coatings are more durable than linings.
- D. linings are more durable than coatings.
Answer: A
NEW QUESTION # 53
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Refuse to take readings until an is in place
- C. Call your supervisor
- D. Develop your own methodology and proceed take the readings
Answer: A
NEW QUESTION # 54
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It contains biocide
- B. It will result in a very slippery surface
- C. The floating structure is stationary
- D. It doesn't contain biocide
Answer: A
NEW QUESTION # 55
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A destructive paint inspection Tooke gauge
- C. A hardness tester
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION # 56
Thermal Spray coatings provide:
- A. Sacrificial protection
- B. Inhibitive protection
- C. Barrier protection
- D. Thermal protection
Answer: A
NEW QUESTION # 57
......
Updated NACE-CIP2-001 Certification Exam Sample Questions: https://troytec.itpassleader.com/NACE/NACE-CIP2-001-dumps-pass-exam.html